Fluke Voltalert 1ac-e Manual

Fluke 2AC VoltAlert™ non-contact voltage tester is easy to use, reliable & they are used to test energized circuits & defective grounds.

• 1000FLT Fluorescent Light Tester Users Manual July 2014 © 2014 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. Vsl#3.

All product names are trademarks of their respective companies. • LIMITED WARRANTY AND LIMITATION OF LIABILITY The main body of this Fluke product will be free from defects in material and workmanship for three years from the date of purchase. The rod extender will be free from defects in material and workmanship for one year from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling. • Table of Contents Title Page Introduction..1 How to Contact Fluke..1 Safety Information..1 Before You Start..3 Power On and Off..3 Battery..3 Beeper On and Off..4 Rod Extender..

4 Controls.. • 1000FLT Users Manual. • List of Tables Table Title Page Symbols..3 1000FLT Features and Controls.. 5 Lamp Test..6 Ballast Test.. 7 Non-Contact Voltage Test..

9 Pin Test..10 Ballast Type Test..12 Replaceable Parts.. • 1000FLT Users Manual. • List of Figures Figure Title Page Rod Extender..4 Optical Sensor for Ballast Type Test.11 Battery Replacement..14 Rod Extender Replacement..15.

• 1000FLT Users Manual. • Safety Information Introduction A Warning identifies conditions and procedures that are The Fluke 1000FLT Fluorescent Light Tester (Product) is dangerous to the user. A Caution identifies conditions and an easy-to-use tool that tests fluorescent lamps, lamp pins, procedures that can cause damage to the Product or the ballasts, and non-contact voltage (NCV). • 1000FLT Users Manual • • Use the Product only as specified, or the When using VoltAlert, if the test indicator does not glow or the beeper does not sound, protection supplied by the Product can be hazardous voltage could still be present. • Beeper Make sure that the Product shipment is complete.

If not,  Battery contact Fluke (see page 1). Install the batteries before you operate the Product. See Battery Replacement for more  Conforms to relevant Australian standards. Information about how to install. • 1000FLT Users Manual When battery power is depleted,  will blink green for 5 2. See Controls section for instructions on how to use the seconds and the Product turns off.

At this battery level, the Product. Product will not work until the batteries are replaced. • Controls The Product has a control button for each type of test and a large LED indicator for test results. Table 2 shows the location and describes each function. 1000FLT Features and Controls Item Description Power On/Off .

• 1000FLT Users Manual Lamp Test Table 3. Lamp Test The Lamp Test verifies that the lamp is gas-filled. This test is done with or without the lamp in the fixture. You can test with the rod extender pulled out or collapsed. • Fluorescent Light Tester Controls Ballast Test Table 4. Ballast Test When you hear a buzzing sound from the fixture or the lamps flicker or do not light up, check the ballast to see if it needs to be replaced. The Ballast Test verifies that the ballast is providing an ac voltage to the fluorescent lamp and senses the presence of the voltage at the filament ends of the lamp.

Fluke 2AC VoltAlert™ non-contact voltage tester is easy to use, reliable & they are used to test energized circuits & defective grounds.

• 1000FLT Fluorescent Light Tester Users Manual July 2014 © 2014 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. Vsl#3.

All product names are trademarks of their respective companies. • LIMITED WARRANTY AND LIMITATION OF LIABILITY The main body of this Fluke product will be free from defects in material and workmanship for three years from the date of purchase. The rod extender will be free from defects in material and workmanship for one year from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling. • Table of Contents Title Page Introduction..1 How to Contact Fluke..1 Safety Information..1 Before You Start..3 Power On and Off..3 Battery..3 Beeper On and Off..4 Rod Extender..

4 Controls.. • 1000FLT Users Manual. • List of Tables Table Title Page Symbols..3 1000FLT Features and Controls.. 5 Lamp Test..6 Ballast Test.. 7 Non-Contact Voltage Test..

9 Pin Test..10 Ballast Type Test..12 Replaceable Parts.. • 1000FLT Users Manual. • List of Figures Figure Title Page Rod Extender..4 Optical Sensor for Ballast Type Test.11 Battery Replacement..14 Rod Extender Replacement..15.

• 1000FLT Users Manual. • Safety Information Introduction A Warning identifies conditions and procedures that are The Fluke 1000FLT Fluorescent Light Tester (Product) is dangerous to the user. A Caution identifies conditions and an easy-to-use tool that tests fluorescent lamps, lamp pins, procedures that can cause damage to the Product or the ballasts, and non-contact voltage (NCV). • 1000FLT Users Manual • • Use the Product only as specified, or the When using VoltAlert, if the test indicator does not glow or the beeper does not sound, protection supplied by the Product can be hazardous voltage could still be present. • Beeper Make sure that the Product shipment is complete.

If not,  Battery contact Fluke (see page 1). Install the batteries before you operate the Product. See Battery Replacement for more  Conforms to relevant Australian standards. Information about how to install. • 1000FLT Users Manual When battery power is depleted,  will blink green for 5 2. See Controls section for instructions on how to use the seconds and the Product turns off.

At this battery level, the Product. Product will not work until the batteries are replaced. • Controls The Product has a control button for each type of test and a large LED indicator for test results. Table 2 shows the location and describes each function. 1000FLT Features and Controls Item Description Power On/Off .

• 1000FLT Users Manual Lamp Test Table 3. Lamp Test The Lamp Test verifies that the lamp is gas-filled. This test is done with or without the lamp in the fixture. You can test with the rod extender pulled out or collapsed. • Fluorescent Light Tester Controls Ballast Test Table 4. Ballast Test When you hear a buzzing sound from the fixture or the lamps flicker or do not light up, check the ballast to see if it needs to be replaced. The Ballast Test verifies that the ballast is providing an ac voltage to the fluorescent lamp and senses the presence of the voltage at the filament ends of the lamp.