Engenius Eoc1650 Firmware Upgrade

Procedure for restoring original firmware for and devices from EnGenius After doing extensive research, i almost find no documentation about this, EnGenius giving no official support on this issue on their site, and the userbase from the Internet found no real solution for this. This procedure applies to devices that had been updated to DD-WRT / OSBRIDGE / OPEN-MESH or any other firmware compatible with EnGenius hardware. My frustration is that, EnGenius included in the product package a flyer that shows you how to update your EOC-1650/2610 to DD-WRT and with a small fineprint, that you have to pay a licence to use that firmware. Personally i consider that not being fair to the users, not to mention that there is no way to go back to your original firmware, in case that you don't like a 3rd-party firmware that you have installed on the device. So, let's begin: First, you have to enter to your device's RedBoot.

Wireless Access Point / Client Bridge / Client Router. 2.4GHz 54Mbps. Upgrading firmware via web browser, setting are reserved after upgrade. View and Download EnGenius EOC1650 user manual online. & Client bridge. Download film tekken sub indo bluray. EOC1650 Wireless Access Point pdf manual download.

Install and configure it to listen to 192.168.1.11 interface, and to serve files from C: engenius - start the redboot.bat file. You will see a cmd window, with text scrolling fast.

- connect the cable to your network card, and power up the device. - after a few seconds, a new window will pop-up, that's putty connected to your device. You will see a prompt RedBoot> At this point, you have successfully conected to your device. Please don't play with cables, power, etc. You may brick for good your device.

Enter the following commands (enter only the bolded text): RedBoot> ip_address -l 192.168.1.1 -h 192.168.1.11 IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0 Default server: 192.168.1.11 RedBoot> fis init -f About to initialize [format] FLASH image system - continue (y/n)? Y *** Initialize FLASH Image System. Erase from 0xbe030000-0xbe7e0000........ Erase from 0xbe7e0000-0xbe7f0000:. Program from 0x81fe0400-0x81ff0400 at 0xbe7e0000:. RedBoot> load -r -b 0x80041000 original2610.bin RedBoot> fis write -b 0x80041000 -l 0x7F0000 -f 0xA8000000 This will take some time, 10-15 minutes, please be patient.

IF your putty window dissapears, don't worry. Leave the device powered on, and after 10-15 minutes, just do a powercycle. RedBoot> reset After this, you may need to powercycle your device. If everything went ok, you should have your firmware restored to original. Just in case, i included all the needed files in this.

Procedure for restoring original firmware for and devices from EnGenius After doing extensive research, i almost find no documentation about this, EnGenius giving no official support on this issue on their site, and the userbase from the Internet found no real solution for this. This procedure applies to devices that had been updated to DD-WRT / OSBRIDGE / OPEN-MESH or any other firmware compatible with EnGenius hardware. My frustration is that, EnGenius included in the product package a flyer that shows you how to update your EOC-1650/2610 to DD-WRT and with a small fineprint, that you have to pay a licence to use that firmware. Personally i consider that not being fair to the users, not to mention that there is no way to go back to your original firmware, in case that you don't like a 3rd-party firmware that you have installed on the device. So, let's begin: First, you have to enter to your device's RedBoot.

Wireless Access Point / Client Bridge / Client Router. 2.4GHz 54Mbps. Upgrading firmware via web browser, setting are reserved after upgrade. View and Download EnGenius EOC1650 user manual online. & Client bridge. Download film tekken sub indo bluray. EOC1650 Wireless Access Point pdf manual download.

Install and configure it to listen to 192.168.1.11 interface, and to serve files from C: engenius - start the redboot.bat file. You will see a cmd window, with text scrolling fast.

- connect the cable to your network card, and power up the device. - after a few seconds, a new window will pop-up, that's putty connected to your device. You will see a prompt RedBoot> At this point, you have successfully conected to your device. Please don't play with cables, power, etc. You may brick for good your device.

Enter the following commands (enter only the bolded text): RedBoot> ip_address -l 192.168.1.1 -h 192.168.1.11 IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0 Default server: 192.168.1.11 RedBoot> fis init -f About to initialize [format] FLASH image system - continue (y/n)? Y *** Initialize FLASH Image System. Erase from 0xbe030000-0xbe7e0000........ Erase from 0xbe7e0000-0xbe7f0000:. Program from 0x81fe0400-0x81ff0400 at 0xbe7e0000:. RedBoot> load -r -b 0x80041000 original2610.bin RedBoot> fis write -b 0x80041000 -l 0x7F0000 -f 0xA8000000 This will take some time, 10-15 minutes, please be patient.

IF your putty window dissapears, don't worry. Leave the device powered on, and after 10-15 minutes, just do a powercycle. RedBoot> reset After this, you may need to powercycle your device. If everything went ok, you should have your firmware restored to original. Just in case, i included all the needed files in this.